Yamaha YFZ45YSSH Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 154

Yamaha YFZ45YSSH Скачать руководство пользователя страница 84

7-17

7

Whenever possible, ride your ATV straight down-
hill. Avoid sharp angles which could allow the ATV
to tip or roll over. Carefully choose your path and
ride no faster than you will be able to react to ob-
stacles which may appear.

CROSSING A SLOPE

WARNING

EWB01633

Improperly crossing hills or turning on hills
could cause loss of control or cause the ATV to
overturn.



Always follow proper procedures as de-
scribed in the Owner’s Manual.



Avoid hills with excessively slippery or loose
surfaces.



Avoid crossing the side of a steep hill.



Shift your weight to the uphill side of the ATV.



Never attempt to turn the ATV around on any
hill until you have mastered the turning tech-
nique as described in the Owner’s Manual on
level ground. Be very careful when turning
on any hill.

Traversing a sloping surface on your ATV requires
you to properly position your weight to maintain
proper balance. Be sure that you have learned the
basic riding skills on flat ground before attempting
to cross a sloping surface. Avoid slopes with slip-
pery surfaces or rough terrain that may upset your
balance.

UBW260E0.book Page 17 Thursday, May 12, 2016 2:28 PM

«
...
82
83
84
85
86
...
»

Содержание YFZ45YSSH



























































































































































Отзывы:

Нет отзывов