Yamaha YFZ45YSSH Скачать руководство пользователя страница 121

Страница: 121 / 154

8-32

Cable length “A” should measure 47–51 mm
(1.85–2.01 in). Adjust the parking brake free play
as follows.

1. Release the parking brake by moving the

parking brake lever to the right.

2. Fully loosen the locknut and the adjusting bolt

at the rear brake caliper.

3. Slide the rubber cover back at the brake ca-

ble.

4. Loosen the locknut.

5. Turn the parking brake free play adjusting nut

in direction (a) to increase the cable length,
and in direction (b) to decrease it.

TIP

If the cable length cannot be adjusted to specifi-
cation, consult a Yamaha dealer.

6. Tighten the locknut on the brake cable.
7. Slide the rubber cover to its original position.
8. Turn in the adjusting bolt at the rear brake cal-

iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.

1. Adjusting bolt
2. Cable length “A”
3. Locknut

1. Locknut
2. Parking brake free play adjusting nut
3. Rubber cover

(b)

(a)

UBW260E0.book Page 32 Thursday, May 12, 2016 2:28 PM

Содержание YFZ45YSSH



























































































































































Результаты поиска

Содержание YFZ45YSSH

Отзывы:

Yamaha YFZ45YSSH, Руководство пользователя, Страница: 121 / 154

Результаты поиска

Содержание YFZ45YSSH

Отзывы: