Yamaha YFZ45YSSH Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 154

Yamaha YFZ45YSSH Скачать руководство пользователя страница 120

8-31

8

of the master cylinders and calipers as well as the
brake hoses replaced at the intervals listed below
or whenever they are damaged or leaking.



Oil seals: Replace every two years.



Brake hoses: Replace every four years.

EBU24395

Checking the front brake lever free
play

The brake lever free play must be checked at the
intervals specified in the periodic maintenance
and lubrication chart. The brake lever should have
no free play as shown. If there is free play, have a
Yamaha dealer check the brake system.

EBU24614

Checking the brake pedal height

The brake pedal height must be checked and, if
necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The top of the brake pedal should be positioned
11.7 mm (0.46 in) below the top of the footrest as
shown. If the brake pedal is not positioned as
specified, have a Yamaha dealer adjust it.

EBU24716

Adjusting the parking brake free play

The parking brake free play must be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.

1. No brake lever free play

1

1. Brake pedal height

1

UBW260E0.book Page 31 Thursday, May 12, 2016 2:28 PM

«
...
118
119
120
121
122
...
»

Содержание YFZ45YSSH



























































































































































Отзывы:

Нет отзывов