Yamaha YFZ45YSSH Скачать руководство пользователя страница 112

Страница: 112 / 154

8-23

8. Wash the sponge material gently but thor-

oughly in solvent.

WARNING! Always use

parts cleaning solvent to clean the sponge
material. Never use low-flash-point sol-
vents or gasoline to clean the sponge ma-
terial because the engine could catch fire
or explode.

[EWB01942]

9. Squeeze the excess solvent out of the

sponge material and let it dry.

NOTICE:

not twist the sponge material when
squeezing it.

[ECB00442]

10. Check the sponge material and replace it if

damaged.

11. Apply Yamaha foam air filter oil or other qual-

ity foam air filter oil to the sponge material.

TIP

The sponge material should be wet but not drip-
ping.

12. Pull the sponge material over the air filter ele-

ment frame.

13. Apply all-purpose grease to the air filter ele-

ment seat.

1. Sponge material
2. Air filter element frame

UBW260E0.book Page 23 Thursday, May 12, 2016 2:28 PM

Содержание YFZ45YSSH



























































































































































Результаты поиска

Содержание YFZ45YSSH

Отзывы:

Yamaha YFZ45YSSH, Руководство пользователя, Страница: 112 / 154

Результаты поиска

Содержание YFZ45YSSH

Отзывы: