Yamaha YFZ45YSSH Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 154

Yamaha YFZ45YSSH Скачать руководство пользователя страница 117

8-28

8

must be adjusted by a Yamaha dealer at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU29602

Brakes

Replacement of brake components requires pro-
fessional knowledge. Brake service should be
performed by a Yamaha dealer.

WARNING

EWB02572

Operating with improperly serviced or adjust-
ed brakes could lead to a loss in braking ability
and an accident.

EBU24131

Checking the front and rear brake pads

The front and rear brake pads must be checked
for wear at the intervals specified in the periodic
maintenance and lubrication chart.

EBU29561

Front brake pads

Each brake pad is provided with wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-

tor grooves. If a brake pad has worn to the point
that the wear indicator grooves have almost dis-
appeared, have a Yamaha dealer replace the
brake pads as a set.

TIP

The wheels need to be removed to check the
brake pads. (See page 8-48.)

EBU29832

Rear brake pads

Each brake pad is provided with wear indicator
grooves, which allow you to check the brake pad
wear without having to disassemble the brake. To
check the brake pad wear, check the wear indica-

1. Wear indicator groove

1

UBW260E0.book Page 28 Thursday, May 12, 2016 2:28 PM

«
...
115
116
117
118
119
...
»

Содержание YFZ45YSSH



























































































































































Отзывы:

Нет отзывов