manualshive.com logo in svg

Yamaha YFM400FAR, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YFM400FAR Скачать руководство пользователя страница 87

3 - 26

CHK

ADJ

CHANGING THE ENGINE OIL/

CLEANING THE AIR FILTER

13.Check:

●

Engine oil pressure

*****************************************************

●

Slightly loosen the oil gallery bolt 

1

.

●

Start the engine and keep it idling until
engine oil starts to seep from the oil gallery
bolt. If no engine oil comes out after one
minute, turn the engine off so that it will not
seize.

●

Check the engine oil passages, the oil filter
cartridge and the oil pump for damage or
leakage. Refer to “CRANKCASE” in
CHAPTER 4.

●

Start the engine after solving the problem(s)
and check the engine oil pressure again.

●

Tighten the oil gallery bolt to specification.

*****************************************************
14.Install:

●

Engine side cover

●

Fuel tank side panel (left)

●

Seat
Refer to “SEAT, CARRIERS, FENDERS
AND FUEL TANK”. 

T

 

R

.

.

Oil gallery bolt:

7 Nm (0.7 m • kg, 5.1 ft • lb)

CLEANING THE AIR FILTER 

NOTE:

There is a check hose 

1

 at the bottom of the

air filter case. If dust and/or water collects in
this hose, clean the air filter element and air
filter case.

Содержание YFM400FAR


































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды