manualshive.com logo in svg

Yamaha YFM400FAR, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YFM400FAR Скачать руководство пользователя страница 324

9 - 17

–

+

ELEC

ELECTRIC STARTING SYSTEM

C0NTINUITY

 

TURNS

3.Starter motor

●

Connect the battery positive terminal 

1

and starter motor cable 

2

 using a jumper

lead 

3

 

.

●

Check the operation of the starter motor.

*

*

WARNING

●

A wire that is used as a jumper lead must
have the equivalent capacity or more as
that of the battery lead, otherwise the
jumper lead may burn.

●

This check is likely to produce sparks, so
be sure that no flammable gas or fluid is
in the vicinity.

*

DOES NOT TURN 

Repair or replace the starter motor.

4.Starter relay

●

Remove the starter relay from the wire
harness.

●

Connect the pocket tester (

Ω

 

×

 1) and the

battery (12 V) to the starter relay terminals.

CONTINUITY

Battery (+) terminal 

→

 

Blue/White terminal 

1

Battery (–) terminal 

→

 

Blue/Black terminal 

2

Tester (+) lead 

→

 Red terminal 

3

 

Tester (–) lead 

→

 Black terminal 

4

 

●

Check the starter relay for continuity.

*

NO CONTINUITY 

Replace the starter relay.

Содержание YFM400FAR


































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды