manualshive.com logo in svg

Yamaha YFM400FAR, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YFM400FAR Скачать руководство пользователя страница 113

3 - 52

CHK

ADJ

CHECKING THE WHEELS/

CHECKING AND LUBRICATING THE CABLES

CHECKING THE WHEELS 

1.Check:

●

Wheel 

1

 

Damage/bends 

→

 Replace.

NOTE:

Always balance the wheel when a tire or wheel
has been changed or replaced.

WARNING

●

Never attempt even small repairs to the
wheel.

●

Ride conservatively after installing a tire
to allow it to seat itself properly on the
rim.

CHECKING AND LUBRICATING THE 
CABLES

WARNING

A damaged cable sheath may cause
corrosion and interfere with the cable
movement. An unsafe condition may result
so replace a damaged cable as soon as
possible.

1.Check:

●

Cable sheath 
Damage 

→

 Replace.

2.Check:

●

Cable operation
Unsmooth operation 

→

 Lubricate or replace.

NOTE:

Hold the cable end up and apply several drops
of lubricant to the cable.

3.Apply:

●

Lithium-soap-based grease
(onto end of the cable)

Recommended lubricant:

Yamaha chain and cable lube or
Engine oil

Содержание YFM400FAR


































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды