manualshive.com logo in svg

Yamaha YFM400FAR, Руководство по обслуживанию

Поделиться
Скачать
Yamaha YFM400FAR Скачать руководство пользователя страница 264

8 - 7

CHAS

FRONT BRAKE

CAUTION:

Disc brake components rarely require
disassembly. DO NOT:

●

disassemble components unless
absolutely necessary;

●

use solvents on internal brake
components;

●

use spent brake fluid for cleaning; (use
only clean brake fluid)

●

allow brake fluid to come in contact with
the eyes, as this may cause eye injury;

●

splash brake fluid onto painted surfaces or
plastic parts, as this may cause damage;

●

disconnect any hydraulic connection, as
this would require the entire brake
system to be disassembled, drained,
cleaned, properly filled and bled after
reassembly.

REPLACING THE FRONT BRAKE PADS

NOTE:

It is not necessary to disassemble the brake
caliper and brake hose to replace the brake
pads.

1.Measure:

●

Brake pad wear limit 

a

 

Out of specification 

→

 Replace the brake

pads as a set.

Brake pad wear limit:

1 mm (0.04 in)

2.Install:

●

Brake pads

●

Brake pad spring

NOTE:

Always install new brake pads, brake pad shim
and brake pad spring as a set.

Содержание YFM400FAR


































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды