manualshive.com logo in svg

Yamaha YFM400FAR, Руководство по обслуживанию

Yamaha YFM400FAR - внедорожный квадроцикл с мощным двигателем. На нашем сайте вы можете скачать бесплатный сервисный мануал для этой модели. Получите инструкцию по обслуживанию и ремонту прямо сейчас на manualshive.com.

Поделиться
Скачать
background image

CHAPTER 8.

CHASSIS

FRONT AND REAR WHEELS 

...................................................................... 8-1

FRONT WHEELS  .................................................................................. 8-1
REAR WHEELS  .................................................................................... 8-2
CHECKING THE WHEELS  ................................................................... 8-3
CHECKING THE WHEEL HUBS ........................................................... 8-3
CHECKING THE BRAKE DISCS  .......................................................... 8-4
INSTALLING THE WHEEL HUBS ......................................................... 8-4
INSTALLING THE WHEELS  ................................................................. 8-4

FRONT BRAKE 

............................................................................................ 8-6

FRONT BRAKE PADS  .......................................................................... 8-6
REPLACING THE FRONT BRAKE PADS  ............................................ 8-7
FRONT BRAKE MASTER CYLINDER  .................................................. 8-9
CHECKING THE MASTER CYLINDER  .............................................. 8-11
ASSEMBLING THE FRONT BRAKE MASTER CYLINDER  ............... 8-11
INSTALLING THE FRONT BRAKE MASTER CYLINDER .................. 8-12
FRONT BRAKE CALIPER ................................................................... 8-14
DISASSEMBLING THE FRONT BRAKE CALIPERS .......................... 8-16
CHECKING THE FRONT BRAKE CALIPERS  .................................... 8-16
ASSEMBLING THE FRONT BRAKE CALIPERS ................................ 8-17
INSTALLING THE FRONT BRAKE CALIPERS  .................................. 8-17

REAR BRAKE 

............................................................................................. 8-19

REMOVING THE REAR BRAKE ......................................................... 8-23
CHECKING THE REAR BRAKE  ......................................................... 8-24
INSTALLING THE REAR BRAKE  ....................................................... 8-25

STEERING SYSTEM 

.................................................................................. 8-28

HANDLEBAR ....................................................................................... 8-28
REMOVING THE REAR BRAKE SWITCH  ......................................... 8-29
CHECKING THE HANDLEBAR  .......................................................... 8-29
INSTALLING THE HANDLEBAR  ........................................................ 8-29
INSTALLING THE REAR BRAKE LEVER  .......................................... 8-29
INSTALLING THE MASTER CYLINDER ASSEMBLY  ........................ 8-30
STEERING STEM  ............................................................................... 8-31
REMOVING THE BEARING RETAINER  ............................................ 8-33
CHECKING THE STEERING STEM  ................................................... 8-33
INSTALLING THE BEARING RETAINER  ........................................... 8-33
INSTALLING THE CABLE GUIDE  ...................................................... 8-33
TIE RODS AND STEERING KNUCKLES  ........................................... 8-34
REMOVING THE STEERING KNUCKLES  ......................................... 8-36
CHECKING THE TIE RODS  ............................................................... 8-36
CHECKING THE STEERING KNUCKLES .......................................... 8-36
INSTALLING THE TIE RODS  ............................................................. 8-39

Содержание YFM400FAR


































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM400FAR

Kazuma Panda Owner'S Manual preview
Panda
Бренд: Kazuma Страницы: 34
Malone MPG460XT Manual preview
MPG460XT
Бренд: Malone Страницы: 37
Taylor-Dunn B0-254-48 Operation, T Roubleshooting And Replacement Parts Manual preview
B0-254-48
Бренд: Taylor-Dunn Страницы: 244
Eton DXL90 Owner'S Manual preview
DXL90
Бренд: Eton Страницы: 30
Trolla 13030 Assembly Instructions Manual preview
13030
Бренд: Trolla Страницы: 11
Hisun AXIS 110 Owner'S Manual preview
AXIS 110
Бренд: Hisun Страницы: 116
Arctic Cat 350 Manual preview
350
Бренд: Arctic Cat Страницы: 70
Arctic Cat 2009 150 Service Manual preview
2009 150
Бренд: Arctic Cat Страницы: 101
Galaxy vans luxury van Owner'S Manual preview
luxury van
Бренд: Galaxy vans Страницы: 60
Gatekeeper Systems CartManager HD Field Technician Manual preview
CartManager HD
Бренд: Gatekeeper Systems Страницы: 60
Taylor-Dunn B0-210-36 Service And Replacement Parts Manual preview
B0-210-36
Бренд: Taylor-Dunn Страницы: 188
Ifor Williams Trailers TT85G Operator'S Manual preview
TT85G
Бренд: Ifor Williams Trailers Страницы: 16
Yamaha KODIAK 700 2018 Owner'S Manual preview
KODIAK 700 2018
Бренд: Yamaha Страницы: 180
Yamaha YFZ450R 2017 Owner'S Manual preview
YFZ450R 2017
Бренд: Yamaha Страницы: 150
Yamaha YFM660FR Supplementary Service Manual preview
YFM660FR
Бренд: Yamaha Страницы: 56
Yamaha YFM660FS Supplementary Service Manual preview
YFM660FS
Бренд: Yamaha Страницы: 478
PARKIT360 FORCE 5K Instruction Manual & User Manual preview
FORCE 5K
Бренд: PARKIT360 Страницы: 13
Columbia Expediter EX-21 2017 Owner'S And Operator'S Manual preview
Expediter EX-21 2017
Бренд: Columbia Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды