background image

 

8-5

 

1

2

3

4

5

6

7

8

9

10

11

 

EBU21864

 

General maintenance and lubrication chart 

 

NO.

ITEM

CHECK OR MAINTENANCE 

JOB

INITIAL

EVERY

Whichev-
er comes 

first

month

1

3

6

6

12

km 

(mi)

320 

(200)

1300 

(800)

2500 

(1600)

2500 

(1600)

5000 

(3200)

hours

20

80

160

160

320

1

Air filter element

 

 

Clean and replace if necessary.

Every 20–40 hours (more often in wet or 

dusty areas)

 

2

 

*

 

Clutch

 

 

Check operation and adjust if necessary.

 

 

3

 

*

 

Front brake

 

 

Check operation and correct if necessary.

 

 

Check fluid level and ATV for fluid leakage, and 
correct if necessary.

 

 

 

Replace brake pads.

Whenever worn to the limit

 

4

 

*

 

Rear brake

 

 

Check operation and correct if necessary.

 

 

Check fluid level and ATV for fluid leakage, and 
correct if necessary.

 

 

 

Replace brake pads.

Whenever worn to the limit

 

5

 

*

 

Brake hoses

 

 

Check for cracks or other damage, and replace if 
necessary.

 

 

 

Replace.

Every 4 years

 

6

 

*

 

Parking brake

 

 

Check operation and adjust if necessary.

 

 

7

 

*

 

Wheels

 

 

Check runout and for damage, and replace if nec-
essary.

 

 

8

 

*

 

Tires

 

 

Check tread depth and for damage, and replace if 
necessary.

 

 

Check air pressure and balance, and correct if 
necessary.

 

 

9

 

*

 

Wheel hub bearings

 

 

Check for looseness or damage, and replace if 
necessary.

 

Содержание YFM25RY



































































































































Отзывы: