Yamaha YFM25RY Скачать руководство пользователя | Manualshive

Страница: 108 / 130

background image

8-36

1

2

3

4

5

6

7

8

9

10

11

Right side

EBU25102

Lubricating the steering shaft

The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU25223

Battery

This model is equipped with a VRLA (Valve Regu-

lated Lead Acid) battery. There is no need to check
the electrolyte or to add distilled water. However,
the battery lead connections need to be checked
and, if necessary, tightened.

NOTICE

ECB00620

Never attempt to remove the battery cell seals,

as this would permanently damage the battery.

WARNING

EWB02160

Battery electrolyte is poisonous and danger-
ous, as it contains sulfuric acid, which can
cause severe burns. Avoid contact with skin,
eyes or clothing. Always shield your eyes
when working near batteries.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten egg
or vegetable oil. Call a physician immediately.
EYES: Flush with water for 15 minutes and get
prompt medical attention.
Batteries produce explosive gases. Keep
sparks, flame, cigarettes or other sources of ig-
nition away. Ventilate when charging or using
in an enclosed space.

1. Upper grease nipple

2. Lower grease nipple

Recommended lubricant:

Lithium-soap-based grease

1

2

«
...
106
107
108
109
110
...
»

Содержание YFM25RY



































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM25RY

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды