Yamaha YFM25RY Скачать руководство пользователя

Страница: 44 / 130

6-2

Position (1):

●

Cold engine start with ambient temperature be-
low 5 °C (40 °F).

Position (2):

●

Cold engine start with ambient temperature be-
tween 0 °C (30 °F) and 30 °C (90 °F).

Position (3):

●

Cold engine start with ambient temperature
above 25 °C (80 °F).

Ambient temp./starter (choke) position

6. Completely close the throttle lever and start

the engine by pushing the start switch.

TIP

If the engine fails to start, release the start switch,
then push it again. Pause a few seconds before
the next attempt. Each cranking should be as short
as possible to preserve battery energy. Do not
crank the engine more than 10 seconds on each

1. Fully open

2. Half open

3. Closed

4. Starter (choke)

Содержание YFM25RY



































































































































Результаты поиска

Содержание YFM25RY

Отзывы:

Похожие инструкции для YFM25RY

Бренды по названию

Популярные бренды

Yamaha YFM25RY, Руководство пользователя

Результаты поиска

Содержание YFM25RY

Отзывы:

Похожие инструкции для YFM25RY

Бренды по названию

Популярные бренды