Yamaha YFM25RY Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 130

Yamaha YFM25RY Скачать руководство пользователя страница 31

4-10

1

2

3

4

5

6

7

8

9

10

11

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18840

Starter (choke)

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on

the starter (choke).
Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.

EBU18890

Seat

To remove the seat

Insert your hand between the rear of the seat and
the rear fender, pull the seat lock lever upward and
pull up the seat at the rear.

1. Arrow mark positioned over “RES”

RES

1

1. Starter (choke)

(a)

(b)

1

«
...
29
30
31
32
33
...
»

Содержание YFM25RY



































































































































Отзывы:

Нет отзывов