Yamaha YFM25RY Скачать руководство пользователя | Manualshive

Страница: 105 / 130

background image

8-33

1

2

3

4

5

6

7

8

9

10

11

small soft brush.

NOTICE

ECB00570

To prevent damaging the O-rings, do not clean
the drive chain with steam cleaners, high-pres-

sure washers or inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a

special O-ring chain lubricant.

NOTICE

ECB00580

Do not use engine oil or any other lubricants
for the drive chain, as they may contain sub-

stances that could damage the O-rings.

EBU24900

Checking and lubricating the cables

The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.

WARNING

EWB02130

Inspect cables frequently and replace if dam-
aged. Corrosion can result when the cable
sheaths become damaged, and cables can
also become frayed or kinked, which could re-
strict the operation of controls and lead to an

accident or injury.

EBU24922

Checking and lubricating the brake and
clutch levers

The operation of the brake and clutch levers
should be checked before each ride, and the lever
pivots should be lubricated if necessary.

Recommended lubricant:

Engine oil

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease

«
...
103
104
105
106
107
...
»

Содержание YFM25RY



































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM25RY

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды