Yamaha YFM25RY страница 102 Скачать руководство пользователя

Страница: 102 / 130

8-30

1. Loosen the locknut at the clutch lever.
2. To increase the clutch lever free play, turn the

adjusting bolt in direction (a), and to decrease
it, turn the bolt in direction (b).

3. Tighten the locknut.

TIP

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-
rectly, have a Yamaha dealer check the internal

clutch mechanism.

EBU26863

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

TIP

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and

all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

1. Clutch lever free play

2. Clutch lever free play adjusting bolt

3. Locknut

(a)

(b)

Drive chain slack:

45.0–55.0 mm (1.77–2.17 in)

Содержание YFM25RY



































































































































Результаты поиска

Содержание YFM25RY

Отзывы:

Похожие инструкции для YFM25RY

Бренды по названию

Популярные бренды

Yamaha YFM25RY, Руководство пользователя

Результаты поиска

Содержание YFM25RY

Отзывы:

Похожие инструкции для YFM25RY

Бренды по названию

Популярные бренды