background image

 

5-3

 

1

2

3

4

5

6

7

8

9

10

11

 

EBU19540

 

Fuel 

 

Make sure that there is sufficient fuel in the tank.
(See page 4-7.)

WARNING

 

EWB00520 

 

 

Do not overfill the fuel tank. Fuel expands
when it heats up. If the fuel tank is overfilled,
fuel could spill out due to heat from the en-
gine or the sun.

 

 

Be careful not to spill fuel, especially on the
engine or exhaust pipe which can cause a
fire and severe injury. Wipe up any spilled
fuel immediately.

 

 

Do not refuel right after the engine has been
running and is still very hot.

 

 

Be sure the fuel tank cap is closed securely.

 

EBU19560

 

Engine oil 

 

Make sure that the engine oil is at the specified lev-
el. Add oil as necessary. (See page 8-10.)

 

EBU19710

 

Front and rear brakes 

 

Brake lever and brake pedal

 

 

Check that there is no free play in the brake le-
ver. If there is free play, have a Yamaha dealer
check the brake system.

 

 

Check for correct brake pedal height. (See
page 8-26.) If the pedal height is incorrect, have
a Yamaha dealer adjust it.

 

 

Check the operation of the lever and pedal. They
should move smoothly and there should be a
firm feeling when the brakes are applied. If not,
have a Yamaha dealer check the brake system.

 

Brake fluid level

 

Check the brake fluid level. Add fluid if necessary.
(See page 8-23.)

 

Brake fluid leakage

 

Check to see if any brake fluid is leaking out of the
pipe joints or brake fluid reservoirs. Apply the
brakes firmly for one minute. If there is any leak-
age, have a Yamaha dealer check the brake sys-

Recommended brake fluid:

DOT 4

Содержание YFM25RY



































































































































Отзывы:

Похожие инструкции для YFM25RY