Yamaha XT250D Скачать руководство пользователя | Manualshive

Страница: 67 / 100

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-29

2

3

4

5

6

7

8

9

EAU23251

Lubricating the rear
suspension

The pivoting points of the rear suspen-
sion must be lubricated by a Yamaha
dealer at the intervals specified in the
periodic maintenance and lubrication
chart.

EAUM1652

Lubricating the swingarm
pivots

The swingarm pivots must be lubricat-
ed by a Yamaha dealer at the intervals
specified in the periodic maintenance
and lubrication chart.

EAU23272

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion.

WARNING! To avoid injury,

securely support the vehicle so
there is no danger of it falling
over.

[EWA10751]

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

Recommended lubricant:

Lithium-soap-based grease

Recommended lubricant:

Lithium-soap-based grease

1YB-9-10.book 29 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
65
66
67
68
69
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Бренд: Qlink Страницы: 44

TroyLee Designs

Бренд: A3 HELMET Страницы: 244

Бренд: RDMOTO Страницы: 2

Бренд: R&G Страницы: 2

Бренд: Salewa Страницы: 17

Бренд: DYNATEK Страницы: 1

Бренд: TVS Страницы: 44

Бренд: Tusk Страницы: 3

Бренд: Shad Страницы: 2

Бренд: Kobalt Страницы: 27

SPIDER MAX GT 500

Бренд: Malaguti Страницы: 104

Бренд: Malaguti Страницы: 172

Бренд: Panther Страницы: 36

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 6

Бренд: KTM Страницы: 100

Raider XL 2014+

Бренд: lehman Trikes Страницы: 38

Бренд: Lehman Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды