Yamaha XT250D Скачать руководство пользователя | Manualshive

Страница: 64 / 100

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-26

1

2

3

4

5

6

7

8

9

EAU23025

Cleaning and lubricating the
drive chain

The drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.

NOTICE

ECA10583

The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.

1. Clean the drive chain with kero-

sene and a small soft brush.

NOTICE:

To prevent damaging

the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.

[ECA11121]

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive

chain with a special O-ring chain
lubricant.

NOTICE:

Do not use

engine oil or any other lubri-
cants for the drive chain, as they

may contain substances that
could damage the O-rings.

[ECA11111]

EAU23095

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca-
bles and cable ends should be lubricat-
ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

WARNING! Damage to the outer
housing of cables may result in in-
ternal rusting and cause interfer-
ence with cable movement. Replace
damaged cables as soon as possi-
ble to prevent unsafe condi-
tions.

[EWA10711]

Recommended lubricant:

Yamaha Chain and Cable Lube or
engine oil

1YB-9-10.book 26 ページ２０１２年３月２７日　火曜日　午前１１時３６分

«
...
62
63
64
65
66
...
»

Содержание XT250D





































































































Отзывы:

Нет отзывов

Похожие инструкции для XT250D

Бренд: Uclear Страницы: 2

Бренд: hepco & becker Страницы: 6

Бренд: APRILIA Страницы: 163

Бренд: B-PWR Страницы: 13

Бренд: R&G Страницы: 9

Бренд: Takegawa Страницы: 2

Бренд: Shark Страницы: 52

Бренд: Honda Страницы: 190

Бренд: Honda Страницы: 137

Бренд: KTM Страницы: 90

Operation and Instruction Manua

Бренд: Takegawa Страницы: 9

Бренд: hepco & becker Страницы: 4

Compu-Fire 55120 32

Бренд: PerTronix Страницы: 3

Бренд: Dynafit Страницы: 20

Бренд: hepco & becker Страницы: 2

Бренд: Yamaha Страницы: 27

Бренд: Yamaha Страницы: 26

Бренд: Yamaha Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды