Yamaha XT250D страница 76 Скачать руководство пользователя

Страница: 76 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

TIP

The drive chain does not need to be
disassembled in order to remove and
install the wheel.

5. Remove the axle nut, washer and

drive chain adjusting plate from the
left-hand side.

6. While supporting the brake caliper,

pull the wheel axle out together
with the drive chain adjusting plate
and washer from the right-hand
side.

7. Remove the spacers and wheel by

pulling the wheel to the back.

NOTICE:

Do not apply the brake

after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
will be forced shut.

[ECA11071]

EAU51631

To install the rear wheel

1. Install the spacers into both sides

of the wheel hub.

2. Install the right side washer, both

drive chain adjusting plates, the
wheel and the brake caliper brack-
et by inserting the wheel axle from

the right-hand side.

TIP



Make sure that the drive chain ad-
justing plates are installed with the
punched sides facing to the out-
side and that the retainer on the
swingarm is inserted into the slot in
the brake caliper bracket.



Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

3. Install the drive chain onto the rear

sprocket, and then adjust the drive
chain slack. (See page 7-24.)

4. Install the left side washer and the

axle nut, and then lower the rear
wheel so that it is on the ground.

1. Axle nut

2. Drive chain adjusting plate

(a)

1. Drive chain adjusting plate

2. Wheel axle

3. Brake caliper

1. Retainer

1YB-9-10.book 38 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды