background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

2

3

4

5

6

7

8

9

weight of rider, passenger, car-
go, and accessories approved
for this model.

WARNING

EWA10511

Never overload your vehicle. Opera-
tion of an overloaded vehicle could
cause an accident.

Tire inspection

The tires must be checked before each
ride. If the tire shows crosswise lines
(minimum tread depth), if the tire has a
nail or glass fragments in it, or if the
sidewall is cracked, have a Yamaha
dealer replace the tire immediately.

TIP

The tire tread depth limits may differ
from country to country. Always comply

with the local regulations.

Tire information

This motorcycle is equipped with tube
tires.
Tires age, even if they have not been
used or have only been used occasion-
ally. Cracking of the tread and sidewall
rubber, sometimes accompanied by
carcass deformation, is an evidence of
ageing. Old and aged tires shall be
checked by tire specialists to ascertain
their suitability for further use.

WARNING

EWA10461

The front and rear tires should be of
the same make and design, other-
wise the handling characteristics of
the vehicle may be different, which
could lead to an accident.

After extensive tests, only the tires list-
ed below have been approved for this
model by Yamaha Motor Co., Ltd.

Tire air pressure (measured on cold 
tires):

0–90 kg (0–198 lb):

Front:

125 kPa (1.25 kgf/cm

2

, 18 psi)

Rear:

150 kPa (1.50 kgf/cm

2

, 22 psi)

90–160 kg (198–353 lb):

Front:

150 kPa (1.50 kgf/cm

2

, 22 psi)

Rear:

175 kPa (1.75 kgf/cm

2

, 25 psi)

Maximum load*:

160 kg (353 lb)

* Total weight of rider, passenger, car-

go and accessories 

1. Tire tread depth

2. Tire sidewall

3. Tire wear indicator

Minimum tire tread depth (front and 
rear):

1.0 mm (0.04 in)

3

2

1

1YB-9-10.book  19 ページ  2012年3月27日 火曜日 午前11時36分

Содержание XT250D





































































































Отзывы: