Yamaha XT250D страница 30 Скачать руководство пользователя

Страница: 30 / 100

INSTRUMENT AND CONTROL FUNCTIONS

4-11

spring preload; the longer distance
A is, the lower the spring preload.

3. Tighten the locknut to the specified

torque.

NOTICE:

Always tighten

the locknut against the adjust-
ing ring, and then tighten the
locknut to the specified
torque.

[ECA10131]

WARNING

EWA10221

This shock absorber assembly con-
tains highly pressurized nitrogen
gas. Read and understand the fol-
lowing information before handling
the shock absorber assembly.



Do not tamper with or attempt to
open the cylinder assembly.



Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.

This may cause the unit to ex-
plode due to excessive gas
pressure.



Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.



Do not dispose of a damaged or
worn-out shock absorber as-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.

1. Locknut

2. Spring preload adjusting ring

1. Distance A

(b)

(a)

Spring preload:

Minimum (soft):

Distance A = 207 mm (8.15 in)

Standard:

Distance A = 197 mm (7.76 in)

Maximum (hard):

Distance A = 187 mm (7.36 in)

Tightening torque:

Locknut:

30 Nm (3.0 m·kgf, 22 ft·lbf)

1YB-9-10.book 11 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Похожие инструкции для XT250D

Бренды по названию

Популярные бренды