Yamaha XT250D Скачать руководство пользователя страница 73

Страница: 73 / 100

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screws.

NOTICE:

Do not over-

tighten the screws, otherwise
the lens may break.

[ECA10681]

EAU24204

Replacing a turn signal light
bulb

1. Remove the turn signal light lens

by removing the screw.

2. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

3. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

4. Install the lens by installing the

screw.

NOTICE:

Do not over-

tighten the screw, otherwise the
lens may break.

[ECA11191]

1. Tail/brake light bulb

1. Screw

2. Turn signal light lens

1. Turn signal light bulb

1YB-9-10.book 35 ページ２０１２年３月２７日　火曜日　午前１１時３６分

Содержание XT250D





































































































Результаты поиска

Содержание XT250D

Отзывы:

Бренды по названию

Популярные бренды

Yamaha XT250D, Руководство пользователя

Результаты поиска

Содержание XT250D

Отзывы:

Бренды по названию

Популярные бренды