Yamaha WR250X страница 94 Скачать руководство пользователя | Manualshive

Страница: 94 / 112

background image

MOTORCYCLE CARE AND STORAGE

8-4

8

3. Perform the following steps to pro-

tect the cylinder, piston rings, etc.
from corrosion.

a. Remove the spark plug cap

and spark plug.

b. Pour a teaspoonful of engine oil

into the spark plug bore.

c. Install the spark plug cap onto

the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)

d. Turn the engine over several

times with the starter. (This will
coat the cylinder wall with oil.)

e. Remove the spark plug cap

from the spark plug, and then
install the spark plug and the
spark plug cap.

WARNING! To

prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.

[EWA10951]

4. Lubricate all control cables and the

pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.

5. Check and, if necessary, correct

the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.

6. Cover the muffler outlet with a

plastic bag to prevent moisture
from entering it.

7. Remove the battery and fully

charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
7-34.

TIP

Make any necessary repairs before
storing the motorcycle.

U32C15E0.book Page 4 Tuesday, July 14, 2009 11:43 AM

«
...
92
93
94
95
96
...
»

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250X

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

Бренд: GIVI Страницы: 3

X-903 Ultra Carbon 29

Бренд: X-lite Страницы: 116

Бренд: Nolan Страницы: 24

Бренд: Honda Страницы: 4

640 LC4 Adventure

Бренд: KTM Страницы: 59

Бренд: DYNATEK Страницы: 4

1003007FONTANASPRINT

Бренд: DYNATEK Страницы: 7

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 63

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 94

Star XV1900AE 2013

Бренд: Yamaha Страницы: 92

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды