Yamaha WR250X страница 48 Скачать руководство пользователя

Страница: 48 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-3

EAU48470

TIP

●

From 19000 mi (31000 km) or 36 months, repeat the maintenance intervals starting from 7000 mi (11000 km) or 12
months.

●

Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service.

EAU17581

Periodic maintenance chart for the emission control system

No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi

(1000 km)

1 month

4000 mi

(6000 km)

6 months

7000 mi

(11000 km)

12 months

10000 mi

(16000 km)

18 months

13000 mi

(21000 km)

24 months

16000 mi

(26000 km)

30 months

Fuel line

• Check fuel hoses for cracks or

damage.

• Replace if necessary.

√

Spark plug

• Check condition.
• Adjust gap and clean.
• Replace at 7000 mi (11000 km)

or 12 months and thereafter every
6000 mi (10000 km) or 12
months.

√

Replace.

√

Replace.

√

Spark arrester

• Clean.

√

Valve clearance

• Check and adjust valve clearance

when engine is cold.

Every 26600 mi (42000 km)

Crankcase breather
system

• Check breather hose for cracks or

damage.

• Replace if necessary.

√

U32C15E0.book Page 3 Tuesday, July 14, 2009 11:43 AM

Содержание WR250X

















































































































Результаты поиска

Содержание WR250X

Отзывы:

Похожие инструкции для WR250X

Бренды по названию

Популярные бренды

Yamaha WR250X, Руководство пользователя

Результаты поиска

Содержание WR250X

Отзывы:

Похожие инструкции для WR250X

Бренды по названию

Популярные бренды