Yamaha WR250X страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 112

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-20

4

With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to “
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.

Does the engine start?

With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.

Does the engine stall?

After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.

Does the engine start?

The system is OK.

The motorcycle can be ridden.

The neutral switch may not be working correctly.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The sidestand switch may not be working correctly.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

The clutch switch may not be working correctly.

The motorcycle should not be ridden

until

checked by a Yamaha dealer.

YES

NO

YES

NO

YES

NO

If a malfunction is noted, have a Yamaha
dealer check the system before riding.

WARNING

”.

U32C15E0.book Page 20 Tuesday, July 14, 2009 11:43 AM

«
...
36
37
38
39
40
...
»

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250X

Бренд: Würth Страницы: 188

Бренд: R&G Страницы: 6

Бренд: Honda Страницы: 91

Бренд: Suzuki Страницы: 440

Бренд: Sym Страницы: 31

Бренд: Sicor Страницы: 2

Dirt Runner 90cc

Бренд: Baja motorsports Страницы: 66

Бренд: R&G Страницы: 24

Бренд: BMW Страницы: 139

MOTO NOSTRA MN4602

Бренд: SC Страницы: 8

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 360

Бренд: Yamaha Страницы: 580

Бренд: Yamaha Страницы: 98

Бренд: JIMS Страницы: 2

VENTURA BIKE-PACK SYSTEM Series

Бренд: DOLD Страницы: 4

Power Commander V

Бренд: Dynajet Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды