Yamaha WR250X страница 83 Скачать руководство пользователя

Страница: 83 / 112

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

EAU24181

Tail/brake light

This model is equipped with an LED-
type tail/brake light.
If the tail/brake light does not come on,
have a Yamaha dealer check it.

EAU43002

Replacing a turn signal light
bulb

1. Remove the turn signal light unit

by removing the screw.

2. Remove the socket (together with

the bulb) by turning it counter-
clockwise.

3. Remove the burnt-out bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the turn signal light unit by

installing the screw.

NOTICE:

not overtighten the screw, oth-
erwise the lens may break.

[ECA11191]

1. Screw

1. Turn signal light unit
2. Turn signal light bulb socket

U32C15E0.book Page 38 Tuesday, July 14, 2009 11:43 AM

Содержание WR250X

















































































































Результаты поиска

Содержание WR250X

Отзывы:

Похожие инструкции для WR250X

Бренды по названию

Популярные бренды

Yamaha WR250X, Руководство пользователя

Результаты поиска

Содержание WR250X

Отзывы:

Похожие инструкции для WR250X

Бренды по названию

Популярные бренды