Yamaha WR250X страница 30 Скачать руководство пользователя | Manualshive

Страница: 30 / 112

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-12

4

3. Wipe up any spilled fuel immedi-

ately.

NOTICE:

Immediately wipe

off spilled fuel with a clean, dry,
soft cloth, since fuel may deteri-
orate painted surfaces or plastic
parts.

[ECA10071]

4. Be sure to securely close the fuel

tank cap.

WARNING

EWA15151

Gasoline is poisonous and can
cause injury or death. Handle gaso-
line with care. Never siphon gaso-
line by mouth. If you should swallow
some gasoline or inhale a lot of gas-
oline vapor, or get some gasoline in
your eyes, see your doctor immedi-

ately. If gasoline spills on your skin,
wash with soap and water. If gaso-
line spills on your clothing, change
your clothes.

EAU13381

NOTICE

ECA11400

Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.

Your Yamaha engine has been de-
signed to use premium unleaded gaso-
line with a pump octane number
[(R+M)/2] of 91 or higher, or a research

octane number of 95 or higher. If
knocking (or pinging) occurs, use a
gasoline of a different brand. Use of un-
leaded fuel will extend spark plug life
and reduce maintenance costs.

Gasohol

There are two types of gasohol: gaso-
hol containing ethanol and that contain-
ing methanol. Gasohol containing
ethanol can be used if the ethanol con-
tent does not exceed 10% (E10). Gas-
ohol containing methanol is not
recommended by Yamaha because it
can cause damage to the fuel system
or vehicle performance problems.

1. Maximum fuel level
2. Fuel tank filler tube

2

1

Recommended fuel:

PREMIUM UNLEADED GASOLINE
ONLY

Fuel tank capacity:

WR25XZ 7.6 L (2.01 US gal,
1.67 Imp.gal)
WR25XZC 7.2 L (1.90 US gal,
1.58 Imp.gal)

Fuel reserve amount (when the fuel
level warning light comes on):

2.1 L (0.55 US gal, 0.46 Imp.gal)

U32C15E0.book Page 12 Tuesday, July 14, 2009 11:43 AM

«
...
28
29
30
31
32
...
»

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250X

Avenger 150 Street

Бренд: Bajaj Auto Страницы: 40

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

Бренд: W-Tec Страницы: 6

Бренд: Ohlins Страницы: 8

Бренд: Nolan Страницы: 24

Бренд: hepco & becker Страницы: 4

Бренд: SUOMY Страницы: 84

Бренд: Shark Страницы: 52

Бренд: Honda Страницы: 130

Бренд: Honda Страницы: 362

Бренд: Big Bike Parts Страницы: 3

Бренд: Fekon Страницы: 24

Бренд: IBEX Страницы: 2

Бренд: Ruroc Страницы: 51

MicroFlooter 8500220

Бренд: Wunderlich Страницы: 2

Бренд: SPEED & STRENGTH Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды