Yamaha WR250X страница 69 Скачать руководство пользователя | Manualshive

Страница: 69 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-24

7

EAU21941

Spoke wheels

WARNING

EWA10610

The wheels on this model are not de-
signed for use with tubeless tires.
Do not attempt to use tubeless tires
on this model.

To maximize the performance, durabil-
ity, and safe operation of your motorcy-
cle, note the following points regarding
the specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage, and
the spokes for looseness or dam-
age before each ride. If any dam-
age is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

EAU48372

Adjusting the clutch lever free
play

The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.

1. Slide the rubber cover back at the

clutch lever.

2. Loosen the locknut.
3. To increase the clutch lever free

play, turn the clutch lever free play
adjusting bolt in direction (a). To

1. Clutch lever free play

2. Locknut (clutch lever)
3. Clutch lever free play adjusting bolt

4. Rubber cover

3

2

1

4

(a)

(b)

U32C15E0.book Page 24 Tuesday, July 14, 2009 11:43 AM

«
...
67
68
69
70
71
...
»

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250X

Бренд: Xenith Страницы: 17

Бренд: Qingqi Страницы: 48

ALK.00.733.15000/B

Бренд: SW-Motech Страницы: 14

Daytona Moto2 765 2020

Бренд: Triumph Страницы: 163

Бренд: Takegawa Страницы: 2

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 130

TorqDrive Clutch Pack

Бренд: Rekluse Страницы: 18

Бренд: Yamaha Страницы: 42

Бренд: Yamaha Страницы: 43

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды