Yamaha WR250X страница 79 Скачать руководство пользователя | Manualshive

Страница: 79 / 112

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-34

7

EAU23291

Checking the wheel bearings

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

EAU46341

Battery

The battery is located behind panel D.
(See page 7-9.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to be
checked and, if necessary, securely
tightened.

WARNING

EWA10760

●

Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe

burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.

• EXTERNAL: Flush with plenty

of water.

• INTERNAL: Drink large quan-

tities of water or milk and im-
mediately call a physician.

• EYES: Flush with water for 15

minutes and seek prompt
medical attention.

●

Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.

●

KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.

To charge the battery

Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the

1. Negative battery lead (black)

2. Positive battery lead (red)

3. Battery

3

2

1

U32C15E0.book Page 34 Tuesday, July 14, 2009 11:43 AM

«
...
77
78
79
80
81
...
»

Содержание WR250X

















































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250X

Бренд: ICON Страницы: 8

Бренд: Yoshimura Страницы: 7

Бренд: SRC Страницы: 5

Бренд: N-Com Страницы: 2

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

EC-SIX DAYS - PART LIST 2011

Бренд: GAS GAS Страницы: 6

Бренд: R&G Страницы: 6

Бренд: Dakota Digital Страницы: 11

H-AFT18-15-01-SL

Бренд: SRC Страницы: 3

Бренд: Sachs Bikes Страницы: 84

Бренд: X-lite Страницы: 33

Liberty 50 Catalyzed 2019

Бренд: PIAGGIO Страницы: 62

Бренд: DYNATEK Страницы: 8

Бренд: Shad Страницы: 12

Бренд: BMW Motorrad Страницы: 28

Бренд: BMW Motorrad Страницы: 170

Бренд: Sealey Страницы: 2

Бренд: BMS Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды