manualshive.com logo in svg

Yamaha WR250F 2022, Руководство по эксплуатации для владельца, Страница: 92 / 404

Поделиться
Скачать
Yamaha WR250F 2022 Скачать руководство пользователя страница 92

PERIODIC MAINTENANCE

3-4

11

* Cylinder

•

Inspect score marks.

•

Inspect wear.

•

Replace.

12

* Clutch

•

Inspect housing, friction plate, 

clutch plate and spring.

•

Replace.

13

* Transmission

•

Inspect.

•

Replace bearings.

14

* Shift fork, shift cam, 

guide bar

•

Inspect wear.

15

* Generator rotor nut

•

Retighten.

16

* Muffler 

•

Inspect and retighten.

•

Clean.

•

Replace.

17

* Crank 

•

Inspect and clean.

18

* Throttle body

•

Inspect.

19

Spark plug

•

Inspect and clean.

•

Replace.

20

Drive chain

•

Lubricate, slack, alignment.

•

Replace.

21

* Cooling system

•

Check coolant level and leakage.

•

Check radiator cap operation.

•

Replace coolant.

Every two years

•

Inspect hoses.

22

Outside nuts and 

bolts

•

Retighten.

23

Air filter

•

Clean and lubricate.

•

Replace.

24

Oil filter

•

Replace.

25

* Engine guard

•

Replace.

26

* Frame

•

Clean and inspect.

27

* Fuel tank, fuel pump

•

Clean and inspect.

28

* Fuel hose

•

Inspect.

•

Replace.

Every four years

29

* Brake(s)

•

Adjust lever position and pedal 

position.

•

Lubricate pivot point.

•

Check brake disc surface.

•

Check fluid level and leakage.

•

Retighten brake disc bolts, caliper 

bolts, master cylinder bolts and 

union bolts.

•

Replace pads.

•

Replace brake fluid.

Every one year

No.

Item

Routine

After 

break-in

Every 

race

Every 

third race 

(or 500 km)

Every 

fifth race 

(or 1000 km)

As 

required

Содержание WR250F 2022





















































































































































































































































































































































































































Отзывы:

Нет отзывов