Yamaha WR250F 2022 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 404

background image

INSTRUMENT AND CONTROL FUNCTIONS

1-21

EAM30188

FRONT BRAKE LEVER

The front brake lever “1” is located on the right
handlebar. Pull it toward the handlebar to acti-
vate the front brake.

EAM30189

REAR BRAKE PEDAL

The rear brake pedal “1” is in the right of the
chassis. Press down on the brake pedal to acti-
vate the rear brake.

EAM30190

SIDESTAND

This sidestand “1” is used to support only the
machine when standing.

WARNING

EWA18980

• Never apply additional force to the sides-

tand.

• Hold up the sidestand before starting out.

EAM30444

STARTER KNOB

Starting a cold engine requires a larger amount
of intake air, which is supplied by the starter
knob “1”.
Pushing the knob toward “a” turns ON the start-
er, resulting in a larger angle of throttle valve.

TIP

When operating the throttle grip in the closing di-
rection, the starter knob “1” moves in the direc-
tion “b” as shown and returns to its original
position.

WARNING

EWA20470

While handling the starter knob, take care

not to burn yourself on exhaust pipes.

EAM30192

FUEL TANK CAP

Fuel tank cap “1” is located under the fuel tank
cap cover “2”.
Remove the fuel tank cap cover to open the fuel
tank cap.

Shift up points

1st



2nd

20 km/h (12 mph)

2nd



3rd

30 km/h (19 mph)

3rd



4th

40 km/h (25 mph)

4th



5th

50 km/h (31 mph)

5th



6th

60 km/h (37 mph)

Shift down points

6th



5th

45 km/h (28 mph)

5th



4th

35 km/h (22 mph)

4th



3rd

25 km/h (16 mph)

3rd



2nd

25 km/h (16 mph)

2nd



1st

25 km/h (16 mph)

1

1

1

a

a

b

b

1

1

«
...
31
32
33
34
35
...
»

Содержание WR250F 2022





















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WR250F 2022

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 288

TRACER 700 2020

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 118

XV1700PCR Road Star Warrior

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 429

Бренд: Yamaha Страницы: 427

Moto matrix YZF-R6S

Бренд: Yamaha Страницы: 41

Бренд: hepco & becker Страницы: 6

Бренд: Puch Страницы: 151

Virago XV1100K(C)

Бренд: Yamaha Страницы: 111

Бренд: Yamaha Страницы: 101

Бренд: HJC Страницы: 9

Бренд: Yamasaki Страницы: 28

Бренд: MSA Страницы: 168

VIKING 2450 Series

Бренд: Lincoln Electric Страницы: 48

Бренд: R&G Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды