Yamaha WR250F 2022 Скачать руководство пользователя страница 136

Страница: 136 / 404

FRONT WHEEL

4-10

EAM30021

INSTALLING THE FRONT WHEEL

1. Install:

•

Front wheel

TIP

Install the brake disc “1” between the brake pads
“2” correctly.

2. Install:

•

Front wheel sensor

•

Front wheel sensor bracket

NOTICE

ECA21020

Make sure there are no foreign materials in

the front wheel sensor rotor and front wheel

sensor. Foreign materials cause damage to

the front wheel sensor rotor and front wheel

sensor.

TIP

When installing the front wheel sensor, check
the wheel sensor lead for twists.

3. Install:

•

Front wheel axle “1”

TIP

Apply the lithium-soap-based grease to the front
wheel axle.

4. Tighten:

•

Front wheel axle nut “1”

NOTICE

ECA24430

Before tightening the front wheel axle nut,

push down hard on the handlebar(s) several

times and check if the front fork rebounds

smoothly.

5. Tighten:

•

Front wheel axle pinch bolt “1”

6. Measure:

•

Distance “a”
(between the wheel sensor rotor “1” and front
wheel sensor “2”)
Out of specification



Check the wheel bear-

Front wheel sensor bolt

7 N·m (0.7 kgf·m, 5.2 lb·ft)

Front wheel axle nut

115 N·m (11.5 kgf·m, 85 lb·ft)

Front wheel axle pinch bolt

21 N·m (2.1 kgf·m, 15 lb·ft)

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды