Yamaha WR250F 2022 Скачать руководство пользователя страница 172

Страница: 172 / 404

FRONT FORK

4-46

5. Remove:

•

Base valve “1”
(from the damper assembly)

TIP

Hold the damper assembly with the cap bolt ring
wrench “2” and use the cap bolt wrench “3” to re-
move the base valve.

EAM30057

CHECKING THE FRONT FORK LEGS

1. Check:

•

Inner tube surface
Scratches



Repair or replace.

Use #1000 grit wet sandpaper.
Damaged oil lock piece



Replace.

•

Inner tube bends
Out of specification



Replace.

Use the dial gauge.

TIP

The bending value is shown by one half of the

dial gauge reading.

WARNING

EWA13650

Do not attempt to straighten a bent inner

tube as this may dangerously weaken it.

2. Check:

•

Outer tube
Scratches/wear/damage



Replace.

3. Measure:

•

Fork spring free length “a”
Out of specification



Replace.

4. Check:

•

Damper assembly “1”
Bend/damage



Replace.

•

O-ring “2”
Wear/damage



Replace.

NOTICE

ECA14200

• The front fork leg has a built-in damper ad-

justing rod and a very sophisticated inter-

nal construction, which are particularly

sensitive to foreign material.

• When disassembling and assembling the

front fork leg, do not allow any foreign ma-

terial to enter the front fork.

5. Check:

•

Base valve “1”
Wear/damage



Replace.

Cap bolt wrench

90890-01500

Cap bolt wrench

YM-01500

Cap bolt ring wrench

90890-01501

Cap bolt ring wrench

YM-01501

Inner tube bending limit

0.2 mm (0.01 in)

Fork spring free length limit

492.0 mm (19.37 in)

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды