Yamaha WR250F 2022 Скачать руководство пользователя страница 337

Страница: 337 / 404

FUEL INJECTION SYSTEM

8-36

Fault code No. 14

TIP

If fault code numbers 13 and 14 are both displayed, perform checkup and repair jobs for fault code num-
ber 13 first.

Fault code No.

Item

Intake air pressure sensor: hose system malfunction (clogged or

detached hose).

Fail-safe system

Able to start engine

Able to drive vehicle

Diagnostic code No.

Diagnostic tool display

Displays the intake air pressure.

Procedure

The atmospheric pressure is displayed on the Yamaha diagnostic tool.

Item

Probable cause of malfunc-

tion and check

Maintenance job

Confirmation of service com-

pletion

The intake air pressure sensor

hose is damaged, discon-

nected, clogged, twisted or

bent.

Repair or replace the sensor

hose.

Start the engine and let it idle for

approximately 5 seconds (fully

close the throttle valve).

Check the condition of the fault

code using the malfunction

mode of the Yamaha diagnostic

tool.

Condition is “Recovered”



to item 3 and finish the service.

Condition is “Detected”



Go to

item 2.

Defective intake air pressure

sensor.

Execute the diagnostic mode.

(Code No. 03)

Atmospheric pressure at the

current altitude and weather

conditions is indicated.

0 m above sea level: About 101

kPa (about 3.63 V)

1000 m above sea level: About

90 kPa (about 3.30 V)

2000 m above sea level: About

80 kPa (about 3.00 V)

3000 m above sea level: About

70 kPa (about 2.70 V)

Value does not change during

cranking



Intake air pressure

sensor replacement.

Service is finished.

Delete the fault code.

Confirm that the fault code has

a condition of “Recovered”

using the Yamaha diagnostic

tool, and then delete the fault

code.

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды