Yamaha WR250F 2022 Скачать руководство пользователя страница 383

Страница: 383 / 404

TROUBLESHOOTING

9-10

EAM30515

TROUBLESHOOTING OF STEERING/HANDLING

Rear suspension is soft

Oil leaking from rear shock

absorber

Replace the rear shock absorber.

Gas leaking from rear shock

absorber

Replace the rear shock absorber.

Fatigued or damaged rear shock

absorber spring

Replace the rear shock absorber.

Improperly adjusted rear shock

absorber spring preload (soft)

Adjust the spring preload.

Improperly adjusted rear shock

absorber rebound damping (soft)

Adjust the rebound damping.

Improperly adjusted rear shock

absorber compression damping

(soft)

Adjust the compression damping.

Oil leaking from rear shock

absorber

Bent, damaged, or corroded rear

shock absorber rod

Replace the rear shock absorber.

Damaged oil seal lip

Replace the rear shock absorber.

Symptom

Possible cause

Actions

Handlebar wobble

Loose lower ring nut

Tighten the lower ring nut to the

specified torque.

Worn bearing or bearing race

Replace the bearing and bearing

race as a set.

Warped front fork

Repair or replace the front fork.

Bent front wheel axle

Replace the front wheel axle.

Incorrect tire pressure

Adjust to the specified tire pres-

sure.

Worn, deformed, or incorrect tire

Replace the tire.

Heavy steering

Lower ring nut is tightened too

tight.

Tighten the lower ring nut to the

specified torque.

Bent lower bracket

Replace the lower bracket.

Broken bearing or bearing race

Replace the bearing and bearing

race as a set.

Incorrect tire pressure

Adjust to the specified tire pres-

sure.

Front wheel vibration

Loose spoke

Tighten the spoke and adjust the

runout.

Damaged or worn wheel bearing

Replace the wheel bearing.

Worn, deformed, or incorrect tire

Replace the tire.

Loose wheel axle or wheel axle

nut

Tighten the wheel axle or wheel

axle nut to the specified torque.

Loose wheel axle pinch bolt

Tighten the wheel axle pinch bolt

to the specified torque.

Incorrect front fork oil level

Adjust to the specified front fork oil

level.

Symptom

Possible cause

Actions

Содержание WR250F 2022





















































































































































































































































































































































































































Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды

Yamaha WR250F 2022, Руководство по эксплуатации для владельца

Результаты поиска

Содержание WR250F 2022

Отзывы:

Похожие инструкции для WR250F 2022

Бренды по названию

Популярные бренды