Yamaha WaveRunner VXS 2015 Скачать руководство пользователя

Страница: 102 / 108

Trouble recovery

(1) Connect the positive (+) jumper cable to

the positive (+) battery terminals of both
batteries.

(2) Connect one end of the negative (–)

jumper cable to the negative (–) battery
terminal of the booster battery.

(3) Connect the other end of the negative (–)

jumper cable to an engine hanger.

(4) Start the engine, and then disconnect the

jumper cables by reversing the steps
above. (See page 27 for information on
starting the engine.)

EJU44050

Replacing the fuses

If a fuse is blown, replace it with the proper
fuse.

To replace a fuse:
(1) Remove the seats and removable water-

tight storage compartment. (See page 43
for seat removal and installation proce-
dures and page 48 for information on the
removable watertight storage compart-
ment.)

Positive (+) jumper cable

Booster battery

Negative (–) jumper cable

Engine hanger

Good fuse

Blown fuse

Good fuse

Blown fuse

UF2W70E0.book Page 96 Tuesday, December 8, 2015 9:03 AM

Содержание WaveRunner VXS 2015













































































































Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды

Yamaha WaveRunner VXS 2015, Руководство владельца/оператора

Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды