Yamaha WaveRunner VXS 2015 страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 108

background image

Instrument operation

41

warning is activated, the maximum engine
speed is limited.

If the engine overheat warning is activated,
immediately reduce the engine speed, return
to shore, and then make sure that water is
being discharged from the cooling water pilot
outlet while the engine is running. If there is
no discharge of water, stop the engine, and
then check the jet intake for clogging. (See
page 94 for information on the jet intake.)

NOTICE:

If you cannot locate and correct

the cause of the overheating, consult a
Yamaha dealer. Continuing to operate at
higher speeds could result in severe en-
gine damage.

[ECJ00042]

EJU43731

Check engine warning

If a sensor malfunction or a short circuit is de-
tected, the check engine warning indicator
and the “WARNING” indicator light blink, and
the buzzer sounds intermittently for 30 sec-
onds.

If the engine is stopped after the check en-
gine warning is activated, the information dis-
play will indicate an error code.

If the check engine warning is activated, im-
mediately reduce the engine speed, return to
shore, and have a Yamaha dealer check the
engine.

EJU43740

Hour meter

The hour meter shows the total number of
hours that the engine has been running since
the watercraft was new.

TIP:

The elapsed time will be kept even if the bat-
tery terminals have been disconnected.

EJU43750

Voltmeter

The voltmeter shows the battery voltage.
When the battery voltage is normal, the volt-
meter displays approximately 12 volts.

1

Hour meter

1

UF2W70E0.book Page 41 Tuesday, December 8, 2015 9:03 AM

«
...
45
46
47
48
49
...
»

Содержание WaveRunner VXS 2015













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VXS 2015

Бренд: Bangor Punta Marine Страницы: 49

Бренд: Kwik Tek Страницы: 3

Бренд: Hobie Страницы: 28

Бренд: Yamarin Cross Страницы: 116

Бренд: Incept Страницы: 4

Бренд: Malibu Boats Страницы: 309

Бренд: Marine Power Страницы: 79

Бренд: elv Страницы: 40

Бренд: Mercury Страницы: 36

Бренд: Mercury Страницы: 40

Бренд: Yamaha Страницы: 515

Бренд: Walker Bay Страницы: 8

MERRY FISHER 855

Бренд: Jeanneau Страницы: 140

WaveRunner FX SVHO 2017

Бренд: Yamaha Страницы: 118

WaveRunner VX Deluxe 2007

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 181

Бренд: Walker Bay Страницы: 13

Бренд: Luhrs Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды