Yamaha WaveRunner VXS 2015 Скачать руководство пользователя

Страница: 49 / 108

Equipment operation

EJU40334

Equipment

EJU42203

Seats

The front and rear seats are removable.
Remove the seats to access the engine com-
partment and removable watertight storage
compartment.
To remove the rear seat:
(1) Pull the rear seat latch up, and then lift up

the rear of the seat.

(2) Pull the seat rearward and remove it.

To install the rear seat:
(1) Insert the projections on the front of the

seat into the stays on the deck.

(2) Push the rear of the seat down to secure-

ly lock it in place.

To remove the front seat:
(1) Remove the rear seat.
(2) Pull the front seat latch up, and then lift

up the rear of the seat.

Seat latch

UF2W70E0.book Page 43 Tuesday, December 8, 2015 9:03 AM

Содержание WaveRunner VXS 2015













































































































Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды

Yamaha WaveRunner VXS 2015, Руководство владельца/оператора

Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды