Yamaha WaveRunner VXS 2015 страница 101 Скачать руководство пользователя | Manualshive

Страница: 101 / 108

background image

Trouble recovery

95

(2) Remove any weeds or debris from

around the jet intake, drive shaft, impel-
ler, jet pump housing, and jet thrust noz-
zle.
If debris is difficult to remove, consult a
Yamaha dealer.

EJU43471

Raising the reverse gate

If the RiDE system malfunctions and the re-
verse gate remains in the lowered position,
the watercraft will not be able to move for-
ward.
After raising the reverse gate so that the wa-
tercraft can move forward, immediately re-
turn to shore and have a Yamaha dealer
service the watercraft.
To raise the reverse gate:
(1) Stop the engine and remove the clip from

the engine shut-off switch.

(2) Enter the water and move to the rear of

the watercraft.

(3) Slide the shift rod joint toward the bow,

and then disconnect the shift rod joint
from the ball joint.

(4) Raise the reverse gate to the forward po-

sition.

TIP:



While the shift rod is disconnected, the re-
verse gate will not move to the neutral po-
sition or reverse position even if the RiDE
lever is squeezed.



If the RiDE lever is squeezed while the shift
rod is disconnected, the watercraft will
move forward.

EJU34642

Jumping the battery

If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables.

EJU34664

Connecting the jumper cables

WARNING

EWJ01251

To avoid battery explosion and serious
damage to the electrical system:



Do not reverse the polarity of the jumper
cables when connecting to the batter-
ies.



Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.



Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.

1

Shift rod joint

2

Ball joint

1

2

1

Reverse gate

2

Forward position

1

2

UF2W70E0.book Page 95 Tuesday, December 8, 2015 9:03 AM

«
...
99
100
101
102
103
...
»

Содержание WaveRunner VXS 2015













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VXS 2015

Cross 57 Bow Rider

Бренд: YAMARIN Страницы: 51

Бренд: NorthStar Страницы: 66

Бренд: NERIS Страницы: 2

Бренд: Boston Whaler Страницы: 80

Бренд: Grand Soleil Страницы: 103

Бренд: Sea-doo Страницы: 116

SAR 2018 Series

Бренд: Sea-doo Страницы: 164

1998 GTX RFI 5666

Бренд: Sea-doo Страницы: 26

Бренд: Johnson Outdoors Страницы: 28

Kayak Itiwit X100 2P

Бренд: Decathlon Страницы: 108

Бренд: LaserPerformance Страницы: 7

Бренд: LaserPerformance Страницы: 17

Бренд: Hunter Страницы: 23

Бренд: Nortik Страницы: 25

Performance 405

Бренд: Baja Страницы: 88

Бренд: Nacra Страницы: 69

Бренд: Hansa Sailing Страницы: 25

Бренд: World Cat Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды