Yamaha WaveRunner VXS 2015 Скачать руководство пользователя | Manualshive

Страница: 69 / 108

background image

Pre-operation checks

63

yard) may not pull free when the operator
falls off, allowing the watercraft to contin-
ue to run and cause an accident.

[EWJ01221]

EJU32676

Switch checks

NOTICE

ECJ01311

Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.

Check the start switch, the engine stop
switch, and the engine shut-off switch for
proper operation. (See pages 27 to 27 for in-
formation on operating each switch.)

To check the operation of the switches:
(1) If the lock mode is selected for the

Yamaha Security System setting, select
the unlock mode. (See page 26 for
Yamaha Security System setting proce-
dures.)

(2) Push the start switch to make sure that

the engine starts.

(3) As soon as the engine starts running,

push the engine stop switch to make
sure that the engine stops immediately.

(4) Restart the engine, and then pull the en-

gine shut-off cord (lanyard) to remove
the clip from the engine shut-off switch
to make sure that the engine stops im-
mediately.

EJU40102

Storage compartment checks

Make sure that the storage compartments
are not damaged and that water has not col-
lected in the compartments. (See page 46 for
information on the storage compartments.)

EJU43800

Fire extinguisher holder, cover, and band
checks

Make sure that the fire extinguisher holder,
cover, and band are not damaged and that
the fire extinguisher is securely held in place
using the band. (See page 48 for information
on the fire extinguisher holder, cover, and
band.)

1

Clip

2

Engine shut-off switch

3

Start switch

4

Engine stop switch

5

Engine shut-off cord (lanyard)

1

2

3

5

4

UF2W70E0.book Page 63 Tuesday, December 8, 2015 9:03 AM

«
...
67
68
69
70
71
...
»

Содержание WaveRunner VXS 2015













































































































Отзывы:

Нет отзывов

Похожие инструкции для WaveRunner VXS 2015

Бренд: O'Day Страницы: 4

Бренд: J/Boats Страницы: 67

Бренд: Hobie Страницы: 15

Бренд: Corsiva Yachting Страницы: 33

Бренд: Corsiva Yachting Страницы: 37

Бренд: Grand Banks Страницы: 41

Бренд: Bavaria Страницы: 26

Бренд: ABSTRACT Страницы: 10

Бренд: WAV Страницы: 21

Nautilus 11 DLX

Бренд: AB Inflatables Страницы: 52

Бренд: TALAMEX Страницы: 17

LEADER 33 OUTBOARD

Бренд: Jeanneau Страницы: 198

Бренд: Jeanneau Страницы: 92

Бренд: NorthStar Страницы: 2

Бренд: NorthStar Страницы: 2

Бренд: Lalizas Страницы: 18

Бренд: Skier's Choice Страницы: 92

Бренд: Marine Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды