Yamaha WaveRunner VXS 2015 Скачать руководство пользователя

Страница: 57 / 108

Operation and handling requirements

(5) Loosen the fuel filler cap and remove it.

(6) Slowly add fuel to the fuel tank.

(7) Stop filling when the fuel level reaches

approximately 50 mm (2 in) from the top
of the fuel tank. Do not overfill the fuel
tank. Because fuel expands when it
heats up, heat from the engine or the sun
can cause fuel to spill out of the fuel tank.

Do not leave the watercraft with a full
tank in direct sunlight.

(8) Wipe up any spilled fuel immediately with

a dry cloth.

(9) Securely install the fuel filler cap by tight-

ening it until it clicks.

(10) Return the hood to its original position,

and then push the hood latch down to
securely lock it in place. Make sure that
the fuel filler cap and the hood are se-

Fuel filler cap

Fuel tank capacity:

70 L (18.5 US gal, 15.4 Imp.gal)

Top of the fuel tank

Approximately 50 mm (2 in) from top of the
fuel tank

Top of the fuel tank

Approximately 50 mm (2 in) from top of the
fuel tank

UF2W70E0.book Page 51 Tuesday, December 8, 2015 9:03 AM

Содержание WaveRunner VXS 2015













































































































Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды

Yamaha WaveRunner VXS 2015, Руководство владельца/оператора

Результаты поиска

Содержание WaveRunner VXS 2015

Отзывы:

Похожие инструкции для WaveRunner VXS 2015

Бренды по названию

Популярные бренды