Yamaha T135S Скачать руководство пользователя страница 221

Страница: 221 / 349

YamahaT135.COM

CARB

CARBURETOR

6-9

EAS00487

ASSEMBLING THE CARBURETOR

Before assembling the carburetor, wash all
of the parts in a petroleum-based solvent.

Always use a new gasket and new O-rings.

1. Measure:

float height

Out of specification

→

Adjust.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Hold the carburetor upside down.
b. Measure the distance from the mating sur-

face of the float chamber (with the gasket
removed) to the top of the float.

NOTE:

The float arm should rest on the needle valve
without depressing it.

c. If the float height is not within specification,

check the needle valve seat and needle
valve.

d. If either the needle valve seat or needle

valve is worn, replace them both.

e. If both the needle valve seat and needle

valve are fine, adjust the float height by
bending the float tang

f. Check the float height again.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

2. Install:

coasting enricher assembly

o-ring

Float height

9.2 mm (0.36 in)

5YP-F8197-E0_6 05.6.27 19:31 Page 9

Yamaha T135 Service Manual

YamahaT135.COM

Содержание T135S






























































































































































































































































































































































Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды

Yamaha T135S, Руководство по обслуживанию

Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды