Yamaha T135S Скачать руководство пользователя страница 235

Страница: 235 / 349

YamahaT135.COM

CHAS

FRONT WHEEL AND BRAKE DISC

7-5

d. Install the new wheel bearings and oil seals

in the reverse order of disassembly.

Do not contact the wheel bearing inner race

or balls

. Contact should be made only

with the outer race

NOTE:

Use a socket

that matches the diameter of

the wheel bearing outer race and oil seal.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

EAS00527

CHECKING THE BRAKE DISC

1. Check:

brake disc
Damage/galling

→

Replace.

2. Measure:

brake disc deflection
Out of specification

→

Correct the brake

disc deflection or replace the brake disc.

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Place the vehicle on a suitable stand so that

the front wheel is elevated.

b. Before measuring the front brake disc

deflection, turn the handlebar to the left or
right to ensure that the front wheel is sta-
tionary.

c. Remove the brake caliper.

d. Hold the dial gauge at a right angle against

the brake disc surface.

e. Measure the deflection 5–10 mm below the

edge of the brake disc.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Brake disc deflection limit (maxi-
mum)

0.15 mm (0.0059 in)

5YP-F8197-E0_7_1 05.6.27 19:29 Page 5

Yamaha T135 Service Manual

YamahaT135.COM

Содержание T135S






























































































































































































































































































































































Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды

Yamaha T135S, Руководство по обслуживанию

Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды