Yamaha T135S Скачать руководство пользователя страница 316

Страница: 316 / 349

YamahaT135.COM

ELEC

8-24

CHARGING SYSTEM

EAS00775

3. Charging voltage

Connect the engine tachometer to the spark
plug lead.

Connect the pocket tester (DC 20 V) to the
battery as shown.

Positive tester probe

→

positive battery terminal

Negative tester probe

→

negative battery terminal

Start the engine and let it run at approxi-
mately 5,000 r/min.

Measure the charging voltage.

NOTE:

Make sure the battery is fully charged.

Is the charging voltage within specification?

Charging voltage

14 V at 5,000 r/min

The charging circuit
is OK.

YES

EAS00776

4. Charging coil resistance

Disconnect the stator coil coupler from the
wire harness.

Connect the pocket tester (

Ω ×

1) to the

charging coil terminals as shown.

Positive tester probe

→

white

Negative tester probe

→

black

Measure the charging coil resistances.

Is the charging coil OK?

YES

EAS00779

5. Wiring

Check the wiring connections of the entire
charging system.
Refer to “CIRCUIT DIAGRAM”.

Is the charging system wiring properly con-
nected and without defects?

YES

Properly connect or
repair the charging
system wiring.

Replace the stator
coil/pickup coil
assembly.

Replace the rectifi-
er/regulator.

Charging coil resistance

0.38–0.58

Ω

at 20°C (68°F) (W – B)

5YP-F8197-E0_8_1 05.6.27 19:27 Page 24

Yamaha T135 Service Manual

YamahaT135.COM

Содержание T135S






























































































































































































































































































































































Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды

Yamaha T135S, Руководство по обслуживанию

Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды