manualshive.com logo in svg

Yamaha T135S, Руководство по обслуживанию

Yamaha T135S - качественный мотоцикл с мощным двигателем. Для обслуживания и ремонта требуется оригинальный Service Manual. Скачайте его бесплатно с нашего сайта. manualshive.com - ваш надежный источник качественных руководств по эксплуатации.

Поделиться
Скачать
background image

YamahaT135.COM

CHK

ADJ

3-32

BLEEDING THE HYDRAULIC BRAKE SYSTEM/ 

ADJUSTING THE DRIVE CHAIN SLACK

NOTE:

Loosening the bleed screw will release the pres-
sure and cause the brake lever to contact the
throttle grip.

h. Tighten the bleed screw and then release

the brake lever.

i. Repeat steps (e) to (h) until all of the air

bubbles have disappeared from the brake
fluid in the plastic hose.

j. Tighten the bleed screw to specification.

k. Fill the brake master cylinder reservoir to

the proper level with the recommended
brake fluid.
Refer to “CHECKING THE BRAKE FLUID
LEVEL”.

w

After bleeding the hydraulic brake system,
check the brake operation.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

Bleed screw

6 Nm (0.6 m·kg, 4.3 ft·lb)

EAS00140

ADJUSTING THE DRIVE CHAIN SLACK

NOTE:

The drive chain slack must be checked at the
tightest point on the chain.

c

C

A drive chain that is too tight will overload
the engine and other vital parts, and one that
is too loose can skip and damage the
swingarm or cause an accident. Therefore,
keep the drive chain slack within the speci-
fied limits.

 5YP-F8197-E0_3_1  05.6.27 20:32  Page 32

Yamaha T135 Service Manual

YamahaT135.COM

Содержание T135S






























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для T135S

Yamaha YZ125(T)/T1 Owner'S Service Manual preview
YZ125(T)/T1
Бренд: Yamaha Страницы: 568
KTM 990 Adventure Baja Owner'S Manual preview
990 Adventure Baja
Бренд: KTM Страницы: 227
APRILIA SHIVER 750 - Brochure preview
SHIVER 750 -
Бренд: APRILIA Страницы: 9
National Cycle Quantum hardcoated N30214-WK Assembly Instructions And Owner'S Manual preview
Quantum hardcoated N30214-WK
Бренд: National Cycle Страницы: 13
X-lite X-1003 Safety And Instructions For Use preview
X-1003
Бренд: X-lite Страницы: 100
HYOSUNG Aquila GT250 R Ej Service Manual preview
Aquila GT250 R Ej
Бренд: HYOSUNG Страницы: 37
Yamaha YZF-R1 Assembly Instructions Manual preview
YZF-R1
Бренд: Yamaha Страницы: 15
Yamaha YW50A Owner'S Manual preview
YW50A
Бренд: Yamaha Страницы: 84
Ear Defender TuneUp H33-M24-L15 User Instruction preview
TuneUp H33-M24-L15
Бренд: Ear Defender Страницы: 64
Cagiva Elefant 650 USA Service Manual preview
Elefant 650 USA
Бренд: Cagiva Страницы: 136
Petzl METEOR Technical Notice preview
METEOR
Бренд: Petzl Страницы: 15
KTM 69130985044 Information preview
69130985044
Бренд: KTM Страницы: 3
KTM 600.12.073.044 Mounting Instructions preview
600.12.073.044
Бренд: KTM Страницы: 13
KTM 450 SMR Owner'S Manual preview
450 SMR
Бренд: KTM Страницы: 100
HealTech Electronics GIpro w/ATRE User Manual preview
GIpro w/ATRE
Бренд: HealTech Electronics Страницы: 4
Honda CRF70F Owner'S Manual preview
CRF70F
Бренд: Honda Страницы: 176
National Cycle Quantum Wash'n'Wipe N30003 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30003
Бренд: National Cycle Страницы: 13
Torrot KidsE10 User Manual preview
KidsE10
Бренд: Torrot Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды