Yamaha T135S Скачать руководство пользователя страница 319

Страница: 319 / 349

YamahaT135.COM

ELEC

8-27

LIGHTING SYSTEM

EAS00788

CHECKING THE LIGHTING SYSTEM

1. The headlight and the high beam indicator

light fail to come on.

The dimmer switch
is faulty. Replace
the left handlebar
switch.

EAS00784

1. Dimmer switch

Check the dimmer switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the dimmer switch OK?

YES

2. Headlight bulb and socket

Check the headlight bulb and socket for con-
tinuity.
Refer to “CHECKING THE BULBS AND
BULB SOCKETS”.

Are the headlight bulb and socket OK?

YES

Replace the head-
light bulb, socket or
both.

3. Voltage

Connect the pocket tester (AC 20 V) to the
headlight and high beam indicator light con-
nectors as shown.

When the dimmer switch is set to “

”.

∫

When the dimmer switch is set to “

”.

Headlight

Positive tester probe

→

green

or yellow

Negative tester probe

→

black

High beam indicator light

Positive tester probe

→

yellow

Negative tester probe

→

black

Set the main switch to “ON”.

Start the engine.

Set the dimmer switch to “

” or “

”.

Measure the voltage (AC 12 V) of green

(yellow

) on the headlight connector (wire

harness side) and yellow

on the meter

assembly connector (wire harness side).

Is the voltage within specification?

YES

Replace the rectifi-
er/regulator.

This circuit is OK.

5YP-F8197-E0_8_1 05.6.27 19:27 Page 27

Yamaha T135 Service Manual

YamahaT135.COM

Содержание T135S






























































































































































































































































































































































Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды

Yamaha T135S, Руководство по обслуживанию

Результаты поиска

Содержание T135S

Отзывы:

Похожие инструкции для T135S

Бренды по названию

Популярные бренды