manualshive.com logo in svg

Yamaha SRCP, Руководство пользователя

Yamaha SRCP - высококачественный продукт, который необходимо сопровождать передовым руководством пользователя. Скачайте бесплатное руководство по эксплуатации на manualshive.com, чтобы получить подробные инструкции и полезные советы о работе с этим устройством. Не упустите возможность сделать использование Yamaha SRCP еще более удобным и эффективным.

Поделиться
Скачать
background image

3-

8

3

I/O INTERF

ACE

3-3 Output Signal Description

3-3

Output Signal Description

The output signals consist of 3 dedicated outputs (READY, BUSY and END), 5 general-purpose
outputs, and feedback pulse outputs. In this section, terms "ON" and "OFF" mean the output transis-
tors are "on" and "off".

3-3-1 Dedicated output

The dedicated outputs are used for exchanging signals between the SRCP controller and an external
device such as a PLC.

■

Ready-to-operate output (READY)

This output is on as long as the SRCP controller system is in normal operation. If an emergency
stop or alarm occurs, then this output turns off to let the motor idle.

• When emergency stop was triggered:

The READY signal turns on again when emergency stop is cancelled.

Operation can be restarted by input of the servo recovery command (SERVO) after canceling
emergency stop.

• When an alarm was issued:

If the READY signal is off while the robot is not in emergency stop, this means that an alarm
was issued. If this happens, correct the problem while referring to Chapter 13, "Troubleshoot-
ing".

In this case, the SRCP controller should be turned off before attempting to restart operation.

■

Command-in-progress output (BUSY)

The BUSY signal is on during execution of a dedicated command input or a command from the
TPB or PC. The BUSY signal turns on when the SRCP controller accepts a dedicated command
input. The dedicated command input should be turned off (contact open) when the BUSY signal
turns on. The BUSY signal turns off when command execution is complete. (At this point, all the
dedicated command inputs must be turned off (contact open).)

c

CAUTION

The dedicated command input must be a pulse input so that it is off when the BUSY signal turns on. If the
command input is left on, the BUSY signal cannot turn off even after the command execution is complete.
As long as the BUSY signal is on, the SRCP controller will not accept other dedicated command inputs or
commands from the TPB or PC. Avoid operating the TPB while the SRCP controller is being operated through
the I/O interface. (Doing so might cause malfunctions during data exchange with a PLC or cause communica-
tion errors on the TPB side.)

■

End-of-run output (END)

The END signal turns off when a dedicated command input is received and turns on when com-
mand execution is complete. The END signal remains off if an error occurs or an interlock or
emergency stop is triggered during command execution.

c

CAUTION

When a reset command or a movement command specifying a very small amount of movement is used, the
command execution time will be very short. In other words, the period that the END signal is off will be very
short (1ms or less in some cases).
The END signal does not change by operation from the TPB or PC.

n

NOTE

The PRM34 (system mode selection parameter) setting can be changed so that the execution result END signal
output for the completed dedicated command occurs only after the dedicated command input turns off. (See section
5-2 "Parameter Description".)

Содержание SRCP























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SRCP

ABB FSCA-01 Manual preview
FSCA-01
Бренд: ABB Страницы: 52
QCON ProX Setup preview
ProX
Бренд: QCON Страницы: 4
Banner SC22-3 Quick Start Manual preview
SC22-3
Бренд: Banner Страницы: 15
bar PCS Series Quick Start preview
PCS Series
Бренд: bar Страницы: 2
Faulhaber MC 5004 Technical Manual preview
MC 5004
Бренд: Faulhaber Страницы: 66
ZIGBEE RC-02 User Manual preview
RC-02
Бренд: ZIGBEE Страницы: 5
Sanhua DPF Series Instructions preview
DPF Series
Бренд: Sanhua Страницы: 3
QED MP50 Instruction Manual preview
MP50
Бренд: QED Страницы: 26
ZKTeco MA500 Installation Manual & User Manual preview
MA500
Бренд: ZKTeco Страницы: 20
ZKTeco ProFace X Installation Manual preview
ProFace X
Бренд: ZKTeco Страницы: 8
ZKTeco TF1600 ZKTeco Quick Start Manual preview
TF1600 ZKTeco
Бренд: ZKTeco Страницы: 10
ZKTeco SpeedFace-V3L User Manual preview
SpeedFace-V3L
Бренд: ZKTeco Страницы: 121
ZKTeco FaceDepot-7BL Quick Start Manual preview
FaceDepot-7BL
Бренд: ZKTeco Страницы: 12
ZKTeco C5S110 Installation And Connection Manual preview
C5S110
Бренд: ZKTeco Страницы: 6
ZiLOG Z8 Encore! XP Quick Start Manual preview
Z8 Encore! XP
Бренд: ZiLOG Страницы: 12
Jäger ADwin HSM-24V Manual preview
ADwin HSM-24V
Бренд: Jäger Страницы: 18
Thorlux Lighting SmartScene IR Remote Series Installation Instructions preview
SmartScene IR Remote Series
Бренд: Thorlux Lighting Страницы: 2
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Бренд: Wavelength Electronics Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды