Yamaha SR10LE Скачать руководство пользователя страница 22

Страница: 22 / 52

The longevity and safety of the snowmo-

bile can be increased by making periodic

checks of the items in the preceding

checklist.
If, at any time, abnormal noises, vibra-

tions, or improper working conditions of

any component of this snowmobile are

detected, DO NOT OPERATE THE

SNOWMOBILE. Take the snowmobile

to an authorized Yamaha Snowmobile

dealer for inspection and adjustment or

repair. If not under warranty, this service

is at the discretion and expense of the

snowmobile owner.
The snowmobile should be taken to an

authorized Yamaha Snowmobile dealer at

the end of each snowmobiling season for

general inspection and for off-season

storage servicing. This inspection and

servicing is at the expense of the snow-

mobile owner.

Fuel System

In-Line Fuel Filter

Yamaha recommends that the in-line fuel

filter be replaced every 8000 km (5000

miles). The filter must be clean to allow

the fuel hose to transmit the amount of

gasoline required.
If the in-line fuel filter is obstructed, gas-

oline flow will be restricted; therefore,

the filter must be replaced. To remove

and install the in-line fuel filter, use the

following procedure:



NOTE: Before removing the fuel fil-

ter, take note that the filter is direc-

tional and the arrow should be

directed towards the engine.



NOTE: The fuel filter is located

below the upper console and to the

right of the steering support. To

access the filter, the access panels

and hood need to be removed.

1. Remove the hose clamps and dis-

card; then slowly remove the fuel

hoses from the fuel filter. Dispose of

the excess fuel from the filter prop-

erly.

2. Inspect the fuel hoses thoroughly for

any signs of cracking, cuts, or wear

points.

3. Place the new hose clamps on the

fuel hoses; then with the fuel pump

inlet and outlet noted, connect the

fuel hoses to the fuel filter. Secure

with the hose clamps.

XM184A



NOTE: After completing the

changing of the fuel filter and the

engine is started for the first time,

inspect the filter area for any signs

of leaks.

Gasoline Additives

Fuel de-icer can be used for all models.

Yamaha Fuel Stabilizer should also be

added to the last tank of gasoline before

storage.

Fuel Pickup Valves

If ever there is a restricted fuel flow and a

pickup valve is suspected, take the snow-

mobile to an authorized Yamaha Snowmo-

bile dealer for this service. If not under

warranty, this service is at the discretion

and expense of the snowmobile owner.

! WARNING

Whenever any maintenance or

inspection is made on the fuel sys-

tem in which there may be fuel leak-

age, there should be no welding,

smoking, open flames, etc., in the

area.

! WARNING

Since the fuel supply hose may be

under pressure, always wear safety

glasses; then remove the hose slowly

to release the pressure. Place an

absorbent towel around the connec-

tion to absorb the fuel.

CAUTION

Make sure the fuel filter is properly

seated into the holder.

Содержание SR10LE





















































Результаты поиска

Содержание SR10LE

Отзывы:

Похожие инструкции для SR10LE

Бренды по названию

Популярные бренды

Yamaha SR10LE, Руководство оператора

Результаты поиска

Содержание SR10LE

Отзывы:

Похожие инструкции для SR10LE

Бренды по названию

Популярные бренды