Yamaha SR10LE Скачать руководство пользователя страница 10

Страница: 10 / 52

Battery

It is extremely important that the battery

be maintained at full charge at all times

and that the battery connections be clean

and tight. If charging the battery becomes

necessary, refer to Battery sub-section in

the Maintenance section.

Jump-Starting



NOTE: Yamaha does not recom-

mend jump-starting a snowmobile

with a dead battery but rather to

remove the battery, service it, and

correctly charge it; however, in an

emergency, it may be necessary to

jump-start a snowmobile. If so, use

the following procedure to carefully

and safely complete this procedure.



NOTE: To access the battery, the

seat must be removed.

1. For the snowmobile to be jump-

started, slide any terminal boots away.

2. Inspect the battery for any signs of

electrolyte leaks, loose terminals, or

bulging sides. Leaking or bulging

battery cases may indicate a frozen

or shorted battery.

3. Inspect the snowmobile to be used for

jump-starting to determine if voltage

and ground polarity are compatible.

The vehicle must have a 12-volt DC,

negative ground electrical system.

4. Move the vehicle to be used for the

jump-start close enough to ensure

the jumper cables easily reach; then

set and lock the brakes, shut off all

electrical accessories, and turn the

ignition switch OFF.



NOTE: Make sure all switches on

the snowmobile to be jump-started

are turned OFF.

5. Disconnect all external accessories

such as cell phones, GPS units, and

radios on both vehicles.

6. Attach one clamp of the positive

(red) cable to the positive (+) termi-

nal (1) of the dead battery (C) being

careful not to touch any metal with

the other clamp; then attach the

other clamp of the positive (red)

cable to the positive (+) terminal (2)

of the good battery (B).

CAUTION

Always turn the ignition switch key to

the OFF position when the snowmo-

bile is not being used. Leaving the

ignition switch in the ON position will

result in discharging the battery and

possible damage to the battery.

! WARNING

Improper handling or connecting of a

battery may result in severe injury

including acid burns, electrical burns,

or blindness as a result of an explo-

sion. Always remove rings and

watches. Any time service is per-

formed on a battery, the following

must be observed: keep sparks, open

flame, cigarettes, or any other flame

away. Always wear safety glasses.

Protect skin and clothing when han-

dling a battery. When servicing a bat-

tery in an enclosed space, keep the

area well-ventilated.

! WARNING

If any of these conditions exist, DO

NOT attempt to jump-start, boost, or

charge the battery. An explosion

could occur causing serious injury.

CAUTION

Always make sure the electrical sys-

tems are of the same voltage and

ground polarity prior to connecting

jumper cables. If not, severe electri-

cal damage may occur.

CAUTION

Failure to disconnect electronic acces-

sories during jump-starting may cause

system damage due to power spikes.

Содержание SR10LE





















































Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды

Yamaha SR10LE, Руководство оператора

Результаты поиска

Содержание SR10LE

Отзывы:

Бренды по названию

Популярные бренды